Targa Miata
MIATA BUILD
January 31, 2007 - A bit of reinforcement for the chassis.
This frame rail reinforcement kit is from our sponsor Flyin' Miata. It slips over the frame rails and provides a surprising improvement in stiffness of the chassis. An added bonus for us - beyond the fact that our 200,000+ mile chassis could use all the help it can get - is that it also armors the underside of the car somewhat and allows us to use the entire length of the frame rail as a jacking point. It's an extra 14.5 lbs, but worthwhile. At least the weight is very low and centered between the wheels!
entry 29 - tags: sponsors, stiffening
January 31, 2007 - The rear bumper cover has been cut up fairly drastically.
Why? Because it will offer less aerodynamic drag. It will allow us to remove some substructure and weight. And also because the car that donated the rear bumper cover had a center exit exhaust, so it had a goofy cut right in the middle of it!
entry 30 - tags: weight loss
February 1, 2007 - Progress continues on preparing the body panels.
The rear bumper supports will be cut down shortly to knock a few pounds off the very back of the car. The passenger's door has been cut up to match the driver's as well. The cage will be welded up this weekend.
entry 31
February 4, 2007 - Now that the bumper cover has been cut down, I've removed the appropriate bits of the car as well.
This frame horn exists primarily to support the tie-down hooks used when the Miata is transported from Japan. There are two of them in the back and they're surprisingly hefty. Well, they were.
entry 32 - tags: weight loss
February 4, 2007 - Behind the rear bumper skin is this large piece of black plastic.
It's pretty light considering, but all we really need are the four small squares of plastic seen sitting on the floor beside it.
entry 33 - tags: weight loss
February 4, 2007 - The dashboard substructure has been beefed up a touch.
I decided than an extra pound or so was worth it for an extremely solidly mounted steering column. There's also no way to remove the dash structure any more, but that's not bothering anyone. One thing that does become obvious when trying to lighten a Miata is just how light Mazda managed to make it in the first place. There aren't any easy places to remove large amounts of weight. The similarly-sized Honda S2000 can drop a significant amount of mass very easily.
entry 34 - tags: weight loss
February 4, 2007 - Time to weld in the cage.
Mark Wingerter from Flyin' Miata came by the garage to handle the welding.
entry 35 - tags: safety
February 4, 2007 - In order for Mark to get full access to some of the tubes, I cut some holes in the body of the car.
It worked quite nicely, allowing him to reach all the way around this awkward joint. The Hard Dog bar is available as a bolt-together design that avoids this kind of problem, but I prefer the weld-in solution better for strength and weight.
entry 36 - tags: safety
February 4, 2007 - About 3 minutes worth of work was required to bolt in the bar once all the welding was done.
It's a lot easier to install a cage in a completely stripped car than a street Miata, that's for sure! The quality of the welding by Hard Dog Fabrication had us all in awe.
entry 37 - tags: safety
February 4, 2007 - Brandon Fitch of Flyin' Miata was also on hand to help out with the cage construction.
He's cutting out some gussets to allow us to tie the cage to the windshield frame for maximum stiffness. Plasma cutters are fun!
entry 38 - tags: safety, stiffness
February 4, 2007 - One of the gussets in place.
Before these were welded in, the windshield frame could be moved slightly independently of the cage. Now, there's no chance.
entry 39 - tags: safety, stiffness
February 4, 2007 - The frame rail reinforcements were bolted in.
You can also see the backing plate for the cage. Between the gusseted cage, the seam welding and these braces the Miata is solid as a rock. The chassis of the car is now ready for paint.
entry 40 - tags: stiffness
February 6, 2007 - Mmmm, painting toys.
Now that the chassis is prepared (and most of the body panels are close), it's time to turn my attention to making the car look like the cool pictures. And this means it's time to learn how to paint.
Luckily, the panels already have decent factory paint with no bodywork so the preparation is easy - just some sanding to scuff the surface. And the fact that there's nothing to mask makes it even easier. That's good, I'll likely need all the help we can get.
In other news, we've found out that while we have to run inner door panels, we don't have to run factory panels. We might still do that as the factory parts are pretty light - but the ones from our donor cars are pretty badly damaged.
entry 41 - tags: paint
February 10, 2007 - The fuel tank was the only thing left in the car that could be removed.
I was going to leave it in for the painting, but at this point it's very simple to remove and I don't have to worry about spraying the rubber hoses in the trunk anymore!
entry 42
February 10, 2007 - We've planned on running a hardtop right from the beginning.
While it would be fun to run as a convertible, we know what the weather in Newfoundland can be like in September! We'd want a top of some sort, and a hardtop with a Lexan rear window is lighter than a soft top. It's also more aerodynamic.
So here it is, our hardtop. It's a little hammered, with chunks missing from the paint and a shattered rear window. As part of a hardtop shuffle, I'm going to end up painting a white hardtop blue and a black hardtop white. It doesn't make sense until you see the pristine, perfect white hardtop beside our damaged black one! The white hardtop is going on a street car instead.
entry 43
February 10, 2007 - When you're in a major project like this, do yourself a favour.
Put little parts in bags and label them. Even if you know the car extremely well - I'd like to think I fall into that category - it makes life much easier.
entry 44 - tags: tips
February 10, 2007 - It's time to start working on the paint job.
First step, make sure the car is clean. It's amazing how many little crevices there are in a modern car. After all, it's essentially fabricated out of sheet steel that's been folded and welded together in a very complex shape. Just how complex becomes clear as you try to get every little corner clean...
entry 45 - tags: paint
February 10, 2007 - Now that the body is clean, it's time to go over it again with wax and grease remover.
Despite the careful cleaning, an extraordinary amount of grime comes off the car.
By the way, I'm learning as I go with this painting gig. If there are any experienced painters out there who see me doing something wrong, don't hesitate to offer advice!
entry 46 - tags: paint
February 10, 2007 - The new paint won't stick to nice shiny baked-on factory paint - which is what we have here - so it's time to scuff it up.
On the interior paint, we're using scotchbrite pads. For the exterior, it's 600 grit sandpaper.
entry 47 - tags: paint
February 10, 2007 - The paint's been scuffed.
Now all I have to do is the final cleaning (again!).
entry 48 - tags: paint